Home / Guides / Powder refresh ratio
Powder refresh ratio: how much virgin powder does a build need?
Quick answer
The refresh ratio is the virgin (new) powder share of the whole powder charge — the rest is powder recovered from previous builds. Manufacturers specify it per grade: the figures published in this database run from 22% (Sinterit PA12 Smooth) to 50% (Formlabs Nylon 12 GF Powder, Arkema Rilsan Invent PA11), with HP specifying 30% for PA 12 Glass Beads. Virgin powder to add = recovered powder × R ÷ (100 − R). Run your own numbers in the refresh ratio calculator.
The manufacturer ratios, in one table
Every figure below is stated by the grade's manufacturer in its own document and is published, with the same source, on the grade's page in this site's material database. Grades whose manufacturers do not publish a figure in the documents this site cites — including the EOS PA12 and PA11 grades — are not given one here.
| Grade | Process | Refresh ratio (virgin share) | Manufacturer wording |
|---|---|---|---|
| Sinterit PA12 Smooth | SLS | 22% | “Material refreshing ratio” — percent of fresh powder mixed with used powder for the next print (powder specification) |
| HP HR PA 12 Glass Beads | MJF | 30% | “Refresh ratio for stable performance” (data sheet recyclability table); the same figure stated as 70% surplus reusability |
| Formlabs Nylon 12 GF Powder | SLS | 50% standard, up to 70% | Standard refresh rate of 50%; up to 70% allowed when troubleshooting defects |
| Arkema Rilsan Invent PA11 | SLS | typically 50% | “Low refreshing factor — typically 50%” (data sheet description) |
Two cautions before comparing the column. First, the ratio is a property of a material-and-machine system, not of PA12 in general — the two 50% SLS figures and the 22% desktop-SLS figure are all PA12-family powders on different systems. Second, a lower ratio is not automatically better: it is only cheaper if part quality holds, which is exactly what the specified ratio is meant to guarantee.
Why powder needs refreshing at all
Only a small share of a powder charge fuses into parts. The rest spends the whole build held just below the melting point — and that heat exposure is powder ageing: the polymer's melt behaviour drifts, build after build, in the powder that was never fused. Reusing 100% of it would concentrate the oldest, most-aged powder indefinitely. Blending in virgin powder at the specified ratio holds the blend's average age — and with it surface quality and mechanical properties — steady. The full definition is in the glossary.
The surplus nobody budgets for
A build returns more unfused powder than the next build can take. The calculator's worked example makes it concrete: a 36 kg charge at a 50% refresh ratio fuses 2 kg of parts and returns 34 kg of used powder — but the next 36 kg charge has room for only 18 kg of it. The other 16 kg is surplus aged powder, discarded in steady state, and the virgin powder actually bought per build is 18 kg, not the 2 kg that ends up in parts. This is why the refresh ratio, together with packing density, decides powder economics: the allowance in the part cost estimator follows the same relation, w = R ÷ p − 1, where p is the packing fraction of the build. Pack builds densely and the surplus per part falls; run sparse builds at a high ratio and most of your powder spend is turnover, not parts.
Running it in practice
- Weigh the cake, not just the parts. Recovered powder U = cake mass − fused part mass. The calculator takes either that pair or a directly weighed U.
- Blend to the ratio, then sieve. Virgin powder V = U × R ÷ (100 − R) at your grade's ratio from the table above; sieving the recovered powder before blending is standard powder handling on every powder-bed platform.
- Track generations when quality drifts. If surfaces degrade, the manufacturer-sanctioned lever is raising the virgin share — Formlabs' guidance for Nylon 12 GF allows up to 70% when troubleshooting — before suspecting the machine.
- Keep grades and colours separate. A refresh calculation only holds within one powder stock; mixing stocks mixes their age profiles and voids the ratio's meaning.
Frequently asked questions
How many times can SLS powder be reused?
There is no fixed cycle count in manufacturer guidance — reuse is controlled by the refresh ratio, not by counting builds. At a 30% refresh ratio (HP PA 12 Glass Beads), each charge replaces 30% of the powder with virgin material, so the stock continuously turns over; the oldest powder is what leaves as surplus. What ends reuse in practice is running below the specified ratio until part quality drifts.
Can I run a 0% refresh ratio — all used powder?
You can physically print that way, but no manufacturer figure in this database sanctions it: the lowest published ratio is 22% (Sinterit PA12 Smooth). Unfused powder ages thermally during every build, and the virgin share is what holds melt behaviour and part properties steady. A 0% run concentrates the oldest powder build after build.
Does the refresh ratio apply to MJF as well as SLS?
Yes — MJF is a powder-bed process with the same recovery loop. HP specifies the ratio per material in its data sheets (30% for PA 12 Glass Beads, in the sheet's recyclability table) and markets the same figure as surplus powder reusability (70% for that grade). SAF works the same way; use the figure for your grade.
What happens if I refresh below the specified ratio?
Manufacturer guidance links under-refreshing to surface defects and drifting mechanical properties — Formlabs, which specifies 50% for Nylon 12 GF Powder, allows raising the ratio to 70% when troubleshooting defects, which is the same mechanism seen from the other side. The saving is real but small next to a failed build: the surplus arithmetic in this guide shows virgin powder per build is mostly set by the ratio and the packing density.
Is a lower refresh ratio always cheaper?
Per build, virgin powder bought equals fused part mass plus surplus discarded, and the surplus grows as the ratio falls — at low packing density a low ratio can discard more aged powder than it saves. The steady-state comparison is worked in the calculator: run your own charge and part mass at two ratios and compare the "virgin powder bought per build" row, not just the blend percentages.
Sources
- Formlabs support — Using Nylon 12 GF (standard refresh rate 50%, up to 70% when troubleshooting), as cited on the grade page
- Arkema Technical Data Sheet — Rilsan® PA11 Invent Nat (refreshing factor typically 50%)
- HP Technical Data Sheet — HP 3D High Reusability PA 12 Glass Beads (doc. 4AA7-0716ENE; refresh ratio 30%)
- Sinterit Powder Specification — PA12 Smooth (document 20201118_EN_V01; refreshing ratio 22%)
Last updated: November 2026