Home / Materials / Sinterit PA12 Smooth
Sinterit PA12 Smooth
PA12PowderSLSSinterit
Quick answer
Sinterit PA12 Smooth is the standard PA12 powder for Sinterit's Lisa-series desktop SLS printers: 32 MPa tensile strength and 10% elongation at break per Sinterit's powder specification (PN-EN ISO 527-2), with a material refreshing ratio of 22% — the lowest manufacturer refresh figure in this database.
PA12 Smooth is the entry powder of the Sinterit ecosystem — the grade the Lisa and Lisa Pro benchtop SLS printers are specified around. Its headline tensile figures (32 MPa, 10% elongation) sit below the industrial SLS grades in this database, which reflects the desktop machine class it is tested on; Sinterit's own specification notes that final part properties vary with part design and orientation.
The figure that stands out is the refreshing ratio: 22%. Sinterit defines it in the specification exactly as this site does — the percent of fresh powder that has to be mixed with used (unsintered) powder for the next print — and a low ratio is the core of the desktop SLS cost argument, because most of every build is recovered powder.
Properties (manufacturer datasheet)
| Property | Value | Orientation / condition | Test standard / note |
|---|---|---|---|
| Tensile strength | 32 MPa | PN-EN ISO 527-2 | |
| Elongation at break | 10 % | PN-EN ISO 527-2 | |
| Charpy impact strength (unnotched) | 16 kJ/m² | PN-EN ISO 179-1 | |
| Further values, as published (ranges & text) | |||
| Charpy impact strength (unnotched) | 16 kJ/m² | PN-EN ISO 179-1/1eU:2010, per Sinterit powder specification | |
| Granulation | 18–90 µm | Per Sinterit powder specification | |
Values are reproduced from the manufacturer source(s) listed below, exactly as published. Properties the manufacturer does not publish are omitted rather than estimated — see the sourcing policy.
Processing notes
- SLS powder for Sinterit Lisa & Lisa Pro printers, per the powder specification.
- Material refreshing ratio 22%: 22% fresh powder mixed with used (unsintered) powder for reuse, per Sinterit's specification footnote.
- Granulation 18–90 µm, per the specification.
Typical applications
- Functional prototypes and small solid parts on desktop SLS
- Complex mechanisms printed as one assembly
- Design models where the Smooth surface finish matters
Manufacturer, process & related entries
Manufacturer
Sinterit is a Polish SLS company based in Kraków, known for the Lisa series of benchtop selective laser sintering printers and its own line of SLS powders. Its PA12 Smooth powder — with a manufacturer refreshing ratio of 22% — is the first Sinterit grade listed in this database.
Process
SLS — Selective Laser Sintering
A laser scans each cross-section over a heated bed of nylon powder, sintering one layer at a time; the surrounding unfused powder supports the part.
Run the numbers for this grade
Two calculators read this database: the part cost estimator prices a part in this grade from its volume and datasheet density, and the refresh ratio calculator plans the virgin-powder blend for a build.
Frequently asked questions
What does Sinterit's 22% refreshing ratio mean?
Per Sinterit's own footnote in the powder specification: the percent of fresh powder that has to be mixed with used (unsintered) powder to be reused in the next print. At 22%, a charge is 22% fresh and 78% recovered powder — a lower virgin share than the 30–50% figures the industrial grades in this database publish.
Why are PA12 Smooth's strength figures lower than EOS PA 2200's?
Different machine class and test setup: PA12 Smooth is specified on Sinterit's Lisa-series desktop printers, PA 2200 on EOS industrial systems. Both are PA12; compare the figures as system-level results (printer + powder + parameters), not as pure polymer rankings.
Which printers run PA12 Smooth?
The specification lists the Lisa & Lisa Pro. Sinterit sells the powder in Starter (first print) and Fresh (refresh) variants of the same grade.
Sources
Last updated: November 2026